Roee Kalinsky's RV-7A Project

Service Bulletins
Home Up News Specifications

 

Back Up

Service Bulletins

This section tracks my project's compliance with service bulletins issued by Van's.

 

SB Number Applies to Description Compliance Status
SB 08-6-1 All RV-10 kits and completed aircraft F-1010 bulkhead reinforcement

Not applicable.

SB 07-11-09

(and FAQ)

All two-place, tricycle gear RV models Nose gear leg and fork upgrade In compliance.

My finish kit was shipped after Feb 2005 and included the upgraded nose gear leg and fork. 

SB 07-4-12 All RV models with electric flaps Securing flap motor rod end bearing Not yet in compliance.

I had already recognized this potential problem and designed my own solution (see "flaps actuator" page), and I believe my solution is superior to Van's.  However, I plan to also install the safety wire per the service bulletin as an extra precaution.

SB 07-2-6 All RV models except RV-3 Affixing the passenger control stick permanently In compliance.

Implemented exactly as described in the service bulletin.

SB 06-9-20 All RV's with manual trim and all RV-10's Trim cable anchor Not applicable.

Not applicable to electric trim.

SB 06-2-23 All models except RV-10 Safetying of standard and flop-type fuel pickup tubes Not yet in compliance.

Will comply.

SB 06-2-3 RV-10 RV-10 vertical stabilizer Not applicable.
SB 05-1-1 RV-7/7A RV-9/9A Tip-up canopy fuselage kits In compliance.

Implemented modifications per the "7/9 TIP-UP NEW CONFIG" kit, i.e. figure 1 of the service bulletin.

SB 04-3-1 Electric flap drive motor Recall Not applicable.

My flap motor assembly is not one of the affected units.

SB 04-2-1 Fuel tanks Inspect fuel tanks Not applicable.

Only applies to RV-6/6A QB and other standard kit wings prior to 2000.  Still, I inspected fuel tanks and found no plastic sheeting.

SB 02-12-1 Firewall forward kits and pre-manufactured hose assemblies Inspect hoses Not applicable.

Only applies to hose assemblies purchased before Dec 10, 2002.

SB 02-6-1 RV-7/7A Larger rudder In compliance.

My empennage kit included the larger rudder.

SB 99-06-1 RV-6/6A Overhead rudder pedals Not applicable.

The recommended gussets are standard on the RV-7/7A.

SB 98-10-1 RV-6A Nose gear check Not applicable.

The "new nose gear leg" had been incorporated into the RV-7A kit, and has since been superseded by a newer nose gear leg (SB 07-11-09).

SB 98-03-1 RV-6/6A Floor pedal reinforcement Not applicable.

The RV-7/7A does not use floor-mounted pedals.

SB 97-05-1 RV-4 Rear seat reinforcement Not applicable.
SB 96-12-1 RV-4 Rudder pedal / cable attach Not applicable.
SB 96-10-3 RV-6/6A Flap motor recall Not applicable.

My flap motor assembly is not one of the affected units.  (See also SB 04-3-1, where this issue cropped up again).

SB 96-10-2 All tailwheel RV aircraft Full swivel tail mechanism Not applicable.

Not applicable to tricycle gear aircraft.

SB 96-10-1 All RV aircraft Filtered airbox TBD.

Does RV-7/7A use these parts?

SB 96-09-1 RV-6A Nosewheel fork Not applicable.

Nose wheel fork has since been redesigned.  Still, I inspected mine and found no cracks.

SB 96-03-1 RV-3 and RV-3A kits and flying aircraft Main wing spar modifications Not applicable.

 

Back Up

 

 

Send mail to roee@kalinskyconsulting.com with questions or comments about this web site.
Copyright © 2003 Roee Kalinsky
Last modified: December 21, 2010

Visit my consulting web site at www.kalinskyconsulting.com for your engineering needs.